That is a tasty looking pie 👍🏻
[img] 
[/img]
I use my attic as a painting studio but the sloping walls mean I can't easily have shelves or any storage. If I do try to store my paints then they are never handy to actually use to I end up with loads of tubes scattered all over the table I use to paint on.
I turned the problem of the sloping walls into a benefit by creating a paint tube hanging rack.
Easy to see the paints and easy to grab a tube and put it back when I am finished. I can also see when I have either no paint of a particular colour or too much off the same one - I am looking at you, Green 359
That's genius Wca 👌
I made a big twinkling letter M for the 21st birthday of my niece, Sarah.
It's about 700mm high and made out of a board of OSB board, board.
Brilliant as always kayak, but... M? Was it just easier than S? I'd have gone with L myself 😆
Brilliant as always kayak, but… M? Was it just easier than S? I’d have gone with L myself
Yeah, an M is much easier... 😂
(only joking, she's called Molly)
🤣
[i]I made a big twinkling letter M for the 21st birthday of my niece, Sarah.[/i]
[i]she’s called Molly[/i]
Obvious really, it is like the 'personal number plates' that only make sense when you swap letters for numbers and ignore the spacing*
I would have quickly glued some tinfoil, or similar, to it to hide the OSB and make it even more shiney
*Normally the end result says "Dubious Choice"
I would have quickly glued some tinfoil, or similar, to it to hide the OSB
😳 I love a bit of OSB.
It looks rad when you smooth it up nice and oil it. All the textures and various shades really pop.
Looks industrial innit.
Agree that OSB works in place, as you say - Instro-chic, just not sure it sets off the lights and cheerful present theme well. Not a criticism, just a different perspective
🙂
A stainless steel "rose" as a Christmas present for Mrs Tillydog.
The base is a lump of beech out of the firewood pile.
Pleased with how it came out, given my lack of artistic ability.
(I might yet smooth off some of the sharp edges in case she doesn't like it 😀 )
Love the flower but the base should be OSB 🙂
Love the flower but the base should be OSB
Ha ha! Thanks, but no way 😀
recently completed a barn conversion, i didnt have much to do with 'making' that, but i did fashion a coffee table out of the barn door...
That flower is lovely, any info on how it's made and with what?
That flower is lovely, any info on how it’s made and with what?
Thank you! 🙂
I didn't take any photos of the work in progress (unusual for me).
The flower petals are 0.5mm thick stainless steel sheet and the stem is 5mm stainless with some blobs of weld & some leaves welded on. Veins on the leaves were embossed with a small chisel.
I cut each layer out with tin-snips and cleaned up the edges with a 'conditioning' disc on the angle grinder - very similar to the method in the video below (there are many others). I turned down and threaded the end of the stem in the lathe though.
There are quite a few templates on line. This looks like the one I used:
Very, very pleased with how it came out - it was originally going to be the trial run.
(Feel free to ask if you want any more info.)
the metal rose is really good.
Very, very pleased with how it came out – it was originally going to be the trial run.
(Feel free to ask if you want any more info.)
Thanks, very interesting. You should be pleased with how it came out 🙂
Nothing exciting but a useful dog washing/drying station.
Very nice Mr beanZ 👌
(copy the 'Direct Link' address and paste it into 'img' box using the menu above)
Thanks for the link tot he video and the tenmplates, I am off to find some 0.5mm stainless to make a flower for MrsWCA Christmas pressie
That dog bath really looks the business. Is it you who has the Wheaten Terriers? Can a dog stand in there, guessing the size means the dog can't move around which is what you want?
Also, that rose is gorgeous as is the industrial style table. Clever peeps!
Classy dog salon.
You can get thumb lever heads that screw directly onto showerhead that would save you having the tap running permanently?
business. Is it you who has the Wheaten Terriers
It is 🙂
Can a dog stand in there, guessing the size means the dog can’t move around which is what you want?
It's just for after walk feet and tummy cleaning,(and dirt riding gear before it goes in the washing machine)the size helps keep them from moving around to much.
You can get thumb lever heads that screw directly onto showerhead that would save you having the tap running permanently
Cheers I shall have a Google.
Thanks Cheesy. Out of interest where did your bath comes from?
@ Merak Free Member
Can you do one to go on top of a Roomba ?
Out of interest where did your bath comes from?
Amazon,I've seen them on ebay aswell.
Refurbed my old 90's Diamond Back MTB. It was a dark blue (originally in 1990 it was Marbled Grey, but it's been blue for over 20 years, until this week.
https://www.flickr.com/photos/166882394@N07/52581729976/in/dateposted-public/
@cheesybeanZ lot's of options, this kind of thing. The other benefit is it doesn't end up pointing upward getting you and your surrounds ringing wet.
I can barely get the dog into the bath not sure I'd get her into your table, I was thinking more get one of those disability walk in baths...
Can't you get something like this plumbed into your front path and then just trigger it as your dog walked over.
Lola would get caught out with that once then that would be diverted.
I like the thinking though.
I found a nice piece of wood in the garage while moving stuff around so made this but realised this afternoon that I don't have any felt to line the drawers, the shops are shut tomorrow and no-one needs any more presents right now so i thought I would post the pictures in the current state incase I stick it on a shelf somewhere and never actually finish it.
Found some felt and superglue
Nowhere near the skill level of the above, but I have been tinkering for the last couple of days and have made a coke can stove, pot stand and heat shield for the princely sum of £2.35.
Tonights tea, Tartiflette (aka Posh Cheesy Chips)
Cool can stove 😊👌
Tartiflette
Where's the rest of it?
Christmas dinner a week late thanks to virus stuff.
Sorry I didn't take pics but I am rather proud of the "chinese" dinner I cooked for 7 of us on new years eve so I'm going to post anyway
Starters - prawn crackers ( of course) sesame butterfly prawns, two types of deep- fried wontons ( bought the pastry but made into wonton by me)
Mains - lemon chicken, Beef with ginger spring onion and bamboo shoots, Sweet and sour pork, chop seuy and egg fried rice. I bought the lemon sauce but made sweet and sour
Every dish was edible and some of it was rather nice. Its really the only creative thing i can do is cook
Colournoise - That burger in the first photo looks a bit undercooked.
Where’s the rest of it?
3 of us ate it. That was the portion sent back for the girl's partner.
Colournoise – That burger in the first photo looks a bit undercooked.
I swear I heard something mooing as I took the first mouthful...
Record shelves for my daughter. Simple stained pine, grove routed in the top, t-slot routed on the back. Not a hard project but also involved building the worlds simplest router table (I'm too much of a coward to route small things hand held)
[url= https://i.ibb.co/RH5qWk6/PXL-20230107-162706000.jp g" target="_blank">https://i.ibb.co/RH5qWk6/PXL-20230107-162706000.jp g"/> [/img][/url]
Nice. They look great 😊👌
Barely hanging together is my millenium falcon. Mounted it vertically using the parts from a horizontal kit. Take the feet off, bodge together the world's shonkiest mount and hang it on some mini meat hooks.
Also needed some parts added to stop the loose top bits from falling off!
I've also fitted a light to show the engines off, but it's not as good as I thought.
I haven't done this, but fully intend to when(and if 😳 ) I get the workshop finished.
As said, not something I've done, but i have done other marquetry- sand shading, fans etc, as well as usual veneering, but I place it in here as an inspiration to others here I know are just as capable.
The process looks simple enough, just very time consuming.
(Theres hundreds of such vids on you tube, and it always pains me when you see a maker with a handful of subscribers, compared to some with millions of subscribers who dont produce anything near as beautiful, but jump about on screen to a catchy tune. 😕
Its a good vid showing the process and pitfalls to avoid. Step by step.And its a good watch all the same if you're into this sort of thing.
If that pains you, wait til you find out there's people who make stuff and don't share it on YouTube at all! 😉
A circle jig for my palm router.
In my Instagram Stories
update when I can get an image to load………
[url= https://i.postimg.cc/xJ3FYtTN/20230204-161128.jp g" target="_blank">https://i.postimg.cc/xJ3FYtTN/20230204-161128.jp g"/> [/img][/url]
[url= https://i.postimg.cc/QHqXBw04/20230206-174159.jp g" target="_blank">https://i.postimg.cc/QHqXBw04/20230206-174159.jp g"/> [/img][/url]
Been sorting out my shed....
Made a TV and speaker stand and got the king of cool up
How much space?!?!? Garage envy
Nice size of workspace. 😀 also envious.
New wheels for the commuter
[img] 
[/img]
that's pretty light, what spec?
Nextie hookless carbon 28mm internal, Chris King R45D, Sapim CX-Ray spokes , Sapim Polyax nipples
My garage gets very cold and as I plan to be making carbon fibre resin infused things in there soon I thought I would add some cheap and easy heating.
Feast your eyes on 'a heater'
Or with instructional labels "A diesel heater"
If you duct the habit air intake inside it will make it more efficient.
Also the wiring get it weather proof its not great quality
Also run it full tilt before shut down keep it from coking up.
But they do work very well
I agree that feeding the warm air intake from within the garage would be more efficient but I can't be bothered to drill another big hole through the garage wall. A 10-15 minute test raised the garage from -1 up to 12 degrees which was ample for me.
I was planning on heat wrapping the wiring to give slightly better weather proofing. What else would you suggest? At the moment the power wires are just two ring connections bolted together to test it works. The other stuff is the connector blocks that came with it.
Wrap it in squirrel fur?
hiw about turning the shelf & back board into a box to enclose the unit?
I think you should also buy a couple of fire extinguishers. The foam type
At the moment the power wires are just two ring connections bolted together to test it works. The other stuff is the connector blocks that came with it.
You are bodging stuff that can kill you and other people if you get it wrong. If water enters that connector block the control box isn't going to be able to do much to regulate the burner. It's supposed to be self-regulating to a degree but it's cheap Chinese crap built from a stolen design at the lowest possible price.
Search for Wiska gel boxes if you want a quick and easy way to do this. I don't understand why you've deliberately taken other wires, left them exposed the elements, but deliberately secured them to the wood with incorrect fittings unless it's to create an industrial aesthetic? I mean, the least you could do is use double-insulated cabling in an IP enclosure.
And a final point is that maybe screwing the thing that's designed to burn diesel to the back of a wooden cupboard door is not the safest route. If it does catch fire it'll melt the diesel container, neatly flooding the whole thing with a fuel source. Don't know how hot the exhaust is but pointing it at a wooden wall also doesn't seem as safe as it could be...
Sorry if this comes across as grumpy but it looks to me as though you haven't considered the risks of what you're doing.
There is a waterproof box that covers the whole thing. I just took it off as the outside of a wooden box doesn't really show much.
[i] don’t understand why you’ve deliberately taken other wires, left them exposed the elements, but deliberately secured them to the wood with incorrect fittings [/i]
The power wires that came with it just ended in metal ring connectors. I used these to connect to the 12V power supply that is inside the garage as a temporary fit to check it actually worked. I fully intend to put something more weather proof and permeant there now I know it works which is why I asked advice on how best to do this.
It is all mounted to a marine ply panel which is bolted to a concrete block wall. The idea is that if I decide to remove it, the whole thing comes down in one piece. The exhaust points at the floor more that the wooden cabin and having held my hand near the exhaust exit and felt the wooden wall after running it for 20 minutes I am happy that little or no heat actually transfers to the wood. I was actually more concerned about the discolouration but it appears to run quite cleanly.
Yes, there is a risk of fire, as with any heat source, but this is meant to be mounted inside a vehicle so hopefully won't want to burst into flames every week. Trawling the internet does show the occasional fire but mostly due to electric faults and punctured or melted fuel lines.
The fuel tank is mounted where it is, on a sloping shelf, to minimise the risk of spillage when filling and to encourage any spillage to drain away from the motor but the baby wipes are there to mop up anything obvious when I fill it. The location also routes the fuel pipe away from the exhaust pipe to minimise the risk of melting - the fuel pipe actually enters the motor between the air in and the exhaust out so needs to be kept pulled to one side to remove the rick of touching the exhaust.
I don't feel upset that you are trying to save my life, I appreciate it, and I will check out the Wiska gel boxes. I was going to use the waterproof car wiring connectors I already have but will see what the differences are. Are you suggesting I replace ALL of the connectors provided or just the power ones?
Aren't you risking a significant chance that the cold air intake will be inhaling the exhaust?
Anyway - wheels for the Spur:
[img] 
[/img]
[img] 
[/img]
I fully intend to put something more weather proof and permeant there now I know it works which is why I asked advice on how best to do this.
At a bare minimum.
IP waterproof junction box for all the wiring. Make sure the wires have a drip loop.
Not sure I'd term a ply boxes "waterproof", particularly given the structure your pic is showing.
Try and vent that exhaust at least up over the roof line, or at least a fair way further from the cold air intake for the air that is heated.
the fuel pipe actually enters the motor between the air in and the exhaust out so needs to be kept pulled to one side to remove the rick of touching the exhaust.
Have you thought about moving the whole lot indoors and running the exhaust tube to the outdoors?
I be he's thought about this....
Have you thought about moving the whole lot indoors
and running the exhaust tube to the outdoors?
But not this...
Have you thought about moving the whole lot indoors andrunning the exhaust tube to the outdoors?
😀
DrP
Boring geek alert.....
Needed a Sulzer/Bayer style static mixer, quoted £3.5k and 10week lead time. Reverse engineered the single 2" element I had in Solidworks and scaled it to suit 3"Schd40 pipe. Tig brazed them.
£140 for 13 elements.
[url= https://i.ibb.co/ChhKnnM/C8-BF60-AD-18-F3-496-F-BF02-450091-D01454.jp g" target="_blank">https://i.ibb.co/ChhKnnM/C8-BF60-AD-18-F3-496-F-BF02-450091-D01454.jp g"/> [/img][/url]
[url= https://i.ibb.co/tmTrkcJ/78-B4-F557-19-D5-45-C7-BB2-D-EDEB8115993-B.jp g" target="_blank">https://i.ibb.co/tmTrkcJ/78-B4-F557-19-D5-45-C7-BB2-D-EDEB8115993-B.jp g"/> [/img][/url]
[url= https://i.ibb.co/BzRD0Mh/757-BBF31-A877-4-DC6-A2-F5-5-B62900-A4994.jp g" target="_blank">https://i.ibb.co/BzRD0Mh/757-BBF31-A877-4-DC6-A2-F5-5-B62900-A4994.jp g"/> [/img][/url]
Just to put some peoples minds at rest:
1) The wiring connectors that were temporarily on show are now properly connected and inside the garage.
2) They are only 12V anyway so unlikely to fry anyone if they get a touch damp.
3) The motor itself is designed to be in a campervan so has a degree of weather proofness built in, plus it is a metal cylinder with a glow plug in it so pretty inert, not a rocket fueled monster.
4) The exhaust needs to be relatively short to keep the back pressure minimal and the engine running well.
5) It is pointing downwards so that the water produced drains rather than rusting through the exhaust.
6) The exhaust area is full of free flowing air and no-one is going to sit there and die from the fumes.
7) The air intake that might suck up exhaust fumes is the one that feeds to motor so gets mixed with diesel and burnt.
8) The air intake that feeds hot air into the garage is inside the box so unlikely to be affected by the external exhaust.
In summary, risk to peoples lives from a 12V supply have been minimised and risk to peoples lives from exhaust fumes minimise by location of exhaust.
Two tanks of fuel used without incident and I planned to be cremated anyway so nothing lost if it does go wrong.
Rustynissanprarie, that's a bloody work of art.
Especially compared to that Heath Robinson lash up shite that WCA posted.
Boring geek alert…..
Well done. But what is it ?.
Some more wheels here - 'Goldix' hubs - which seems like DT 240 copies, and WindWing rims at 430g each for 30mm (internal) 27.5" AM weight. They feel utterly bombproof. No access holes for the nipples which I was a bit nervous about, but lacing only took slightly longer than normal using a magnet to draw the nips around from the valve hole. I might feel differently if I was a pro wheelbuilder with the extra faff, but as a one off it's quite nice to have a rim that won't need tape.
No access holes for the nipples which I was a bit nervous about, but lacing only took slightly longer than normal using a magnet to draw the nips around from the valve hole.
Crikey, what a faff, but a cracking result 👌
Needed a Sulzer/Bayer style static mixer,
A what now?
Also in the don't know what they are but very impressed camp. 😊👏
A 'ball in a box'
(Playing with the last-but-one thing I made - a small CNC machine)
Oi tillydog,where's the timelapse film to go with that? 🙃🤣
Nice work 👍
Ta - The CNC is a homebrew affair:
(I've re-designed the spindle since those photos were taken)
More info here (my website) or here (MIG Welding forum).
🙂
Some more wheels here – ‘Goldix’ hubs – which seems like DT 240 copies, and WindWing rims at 430g each for 30mm (internal) 27.5″ AM weight. They feel utterly bombproof.
That does look very faffy, but amazing result.