Forum menu
cx brakes
 

[Closed] cx brakes

Posts: 916
Free Member
Topic starter
 

1st off road ride on the new cx bike today, wet and muddy!

Had forgotten how crap in the wet are rim brakes.

Currently cantilevers, are v brakes better?

Frame is non disc mount but fork has a mount, thinking mechanical disc on front?

Anyone know a set of wheels which are disc and rim brake compatible?


 
Posted : 23/06/2013 8:38 pm
Posts: 66105
Full Member
 

I stuck a set of cheapo BMX Vs on mine, even with standard pads they work better than any cantis I've used. Mud clearance is fractionally less good mind, but never been problematic. Only slight hassle is needing to add a barrel adjuster so that you can get the wheel in and out!

Haven't used discs on a crosser though.


 
Posted : 23/06/2013 8:41 pm
Posts: 3509
Free Member
 

yes, trp v brakes are very good (not far off disc power imo)!


 
Posted : 23/06/2013 8:43 pm
Posts: 0
Free Member
 

I had standard MTB vees with travel adapters on my CX before getting discs. They worked very well, the only downside was that rim wear was still there.


 
Posted : 23/06/2013 8:49 pm
Posts: 0
Free Member
 

I e tried quite a few brakes on my cx bike and the best by a long long way are avid ultimates.


 
Posted : 23/06/2013 8:52 pm
Posts: 0
Free Member
 

The pads make a massive difference, the pads the bike came with are probably cheap crappy ones (an easy way for the manufacturer to save money/increase margins).


 
Posted : 23/06/2013 8:55 pm
Posts: 0
Free Member
 

I bought Dia compe MX 2 v's and levers.

Stock pads where ok, but once worn i switched over to a set of Aztec cartridge pads.
Being stiffer units the difference in braking performance was a drastic improvement.

If your brakes don't have cartridge pads, then a good set will improve things and be cheaper than a new brakeset.

Faff to set up, but once dialled in, swapping out pads is a doddle, remove split pin, push out worn pad from cartridge, clean cartridge with old toothbrush, push in new pads and off you go


 
Posted : 23/06/2013 9:02 pm
Posts: 916
Free Member
Topic starter
 

yellow swiss stop pads on it?


 
Posted : 23/06/2013 9:14 pm
Posts: 0
Free Member
 

seconded TRP the mini V's on my Kaff are unbelievable

I am NOT considering a Disc framset now

Ok £70 sounds a hit but how much is a new frameset and wheels


 
Posted : 23/06/2013 9:17 pm
 aP
Posts: 681
Free Member
 

I use swisstop green pads with Tektro cantilevers. They're fine. I am about to change to Campag cx cantilevers on the No1 bike though and put the Tektro brakes onto my islabike.


 
Posted : 23/06/2013 9:23 pm
Posts: 4338
Free Member
 

I've got single digit and travel agents on mine

[img] [/img]

[img] [/img]


 
Posted : 23/06/2013 9:26 pm
Posts: 916
Free Member
Posts: 916
Free Member
Posts: 0
Free Member
 

Great variation in cantis, most are crap, some are actually good


 
Posted : 23/06/2013 10:07 pm
Posts: 0
 

Personally hate froglegs with a passion, they invariably squeel as there is not enough adjustment via the fiddly pad adjuster, and on some frames they just vibrate and cause fork flutter.

Best I have used by a long stretch are the avid ultimates, the standard avid pads aren't bad, currently using the BBB blue ones for better braking when it's wet. Don't forget you don't want all out power, you want control and feel.


 
Posted : 23/06/2013 10:11 pm
Posts: 0
Free Member
 

+1 frogglegs, i've got trp euroX magnesiums that are ridiculously expensive and a set of frogglegs and they perform pretty much identical and look identical..
frogglegs £40 trp eurox mags £200.. salmon pads and set up right you get all the braking power you need for cx riding..there good enough for most of the pro's..


 
Posted : 23/06/2013 10:18 pm
Posts: 3136
Full Member
 

Tektro 720's are very good for the money.. Super easy to set up and really work well 🙂


 
Posted : 23/06/2013 11:10 pm
Posts: 5047
Full Member
 

if you do eventually go for discs, avoid tektro lyra like the ****in plague, utterly useless.
you would be better off holding up a postage stamp and using it as an air brake.


 
Posted : 23/06/2013 11:55 pm
Posts: 1646
Full Member
 

Travel Agents are great until they get some grit/dirt in them, I've gone to Tektro Mini V's less power but lots more reliable and less faff.


 
Posted : 24/06/2013 1:52 am
Posts: 0
Free Member
 

I was told that before getting them but never found it an issue. Maybe mud is just scared of me? I did some horrendously muddy rides with them and it never seemed to have any effect.


 
Posted : 24/06/2013 10:52 am
Posts: 66105
Full Member
 

FWIW you don't need travel agents, just need the right Vs. I can never remember which ones I used to pair with my 5600s, mind, but just a case of getting the length right.


 
Posted : 24/06/2013 10:58 am
Posts: 4338
Free Member
 

I was told that before getting them but never found it an issue. Maybe mud is just scared of me? I did some horrendously muddy rides with them and it never seemed to have any effect.

same here.. used them in anger at 3 very muddy races last year and a summer cross race the other week. Worked absolutely fine


 
Posted : 24/06/2013 11:46 am
Posts: 916
Free Member
Topic starter
 

ok
v brakes, does it need to be mini v brakes?


 
Posted : 24/06/2013 12:19 pm
 GDRS
Posts: 0
Full Member
 

A bit of a hijack - can anyone recomend me a good set of brake levers for using with canti's (Frogs) - but for a single speed set up. Currently have some diacompe jobs - not good at all.


 
Posted : 24/06/2013 12:31 pm
Posts: 3136
Full Member
 

Sram levers(for ss) are super comfy.. Or on a budget tektro ones are comfy too and around £15 off the bay


 
Posted : 24/06/2013 1:10 pm
Posts: 6851
Full Member
 

BB7 front, tektro rear for me. Fine for Lakes/3 peaks type riding.


 
Posted : 24/06/2013 7:05 pm
Posts: 0
Free Member
 

Cane Creek scr-5 on my ss but I like the look of the TRP levers


 
Posted : 24/06/2013 10:35 pm