my bottlerocket has a 30.0 seat post i want to get a 30.9 uppy downy posty wosty, so should i get it reamed or go the 27.2 route with shims?
ta 
Bike Forum
to ream or not to ream, that is the question
-
Posted 6 months ago #
-
That's a lot to take off!What's the wall thickness?
Being a transition its probly about 5mm!Posted 6 months ago # -
dunno
Posted 6 months ago # -
Shims
Posted 6 months ago # -
What size seatpost clamp?
Posted 6 months ago # -
shims...the metal is not thick enough to withstand the removal of 4.5 mm IMHO. you would be removing over 50% of the metal if not it all IMHO.
Posted 6 months ago # -
dunno 2010 bottlerocket
Posted 6 months ago # -
tricky one!
will you be raising and lowering the post in the frame too? or is the 125mm adjustment gonna be enough for all your riding? if the latter I'd probably go with a shim (despite absolutely hating seatpost shims)
reaming for me would depend on how much seattube material there is and how low it needs reamed to.
I'd ask Transition's opinion?Posted 6 months ago # -
junkyard we're only talking 0.45mm here
Posted 6 months ago # -
Junkyard - 0.45mm!
Posted 6 months ago # -
Ok let's assume it's 34.9mm.That makes the wall thickness 2.45mm. Ream 0.9 mm and the wall thickness is 2mm which is 20% less. Which is a lot.
Posted 6 months ago # -
So it has a 34.9mm seat tube clamp. There are plenty of frames that use a 30.9mm post with a 34.9mm seat clamp (specialised being one)
I'd guess transition specced it with a 30mm seat post for a bit more material and a bit extra strength, personally I think you'd be ok.
Posted 6 months ago # -
If it's decent aluminium and the seatpost isn't super extended when you are pedalling I'd ream it - PITA to do tho.
ST will likely be the same diameter on the outside - 34.9mm
Posted 6 months ago # -
davidtaylforth - Member
I'd guess transition specced it with a 30mm seat post for a bit more material and a bit extra strength, personally I think you'd be ok.Or cos it's crap alu?
Posted 6 months ago # -
Or cos it's crap alu?
All Alu is crap, steel is real and titanium is magic.
Posted 6 months ago # -
I'd be tempted to ream it Tony, it's only 0.9 off the diameter, maybe ask Surf sales and see what they say
Posted 6 months ago # -
How much would you get away with taking off the dropper post?
Maybe take the frame halfway to one of the more obscure sizes (not sure which actually exist but I imagine there is a 30.4 or 30.6 out there somewhere?)Also if its the 27.2mm route, then you could always try lightly sticking the shim inside the frame somehow, keep the post/shim greased a little and it should stop there?
EDIT:
30.4mm posts if you wanted to ream halfway with the frame and want a normal seatpost for some reason. Would still need to take 0.25mm out the walls of a dropper post thoughPosted 6 months ago # -
There's an easy solution:
turn the 0.9 seatpost down to 30.0.
SImples!
Posted 6 months ago # -
If you do just don't sit down too hard
its been done before I've seen a picc some where.
Posted 6 months ago # -
Al will glue one on for you.
Posted 6 months ago # -
hmmmm maybe 27.2 and shim then
Posted 6 months ago # -
Jedi, we've (at 18 Bikes) have done exactly that a couple of times on Bottlerocket frames perfectly successfully. There's plenty of material as the frames are so overbuilt. Just find a descent LBS or machine shop and they shouldn't have any trouble at all
Posted 6 months ago # -
really? oh that is rad!
if i cant find someone local i may pop up. how much?sounds wrong to ask for a reaming
Posted 6 months ago # -
Yup, done a couple of frames at least. It needs to be done slowly with an adjustable reamer, before using the 30.9mm reamer to get a good job but isn't difficult as such.
Probably be about £20 or so depending on how long it takes
Posted 6 months ago # -
is it a book it in job or turn up and chill for a couple of hours?
Posted 6 months ago # -
Would be better to give us a shout before turning up so we can make sure we have the rights tools at the shop rather than the frame-building workshop
Posted 6 months ago # -
I tried so hard to get the decimal point tin the right place as well
and 
Posted 6 months ago # -
Personally I would say its far too much to ream out and you will leave a stress raiser at the bottom of the reamed out section.
I(t might be OK but you are removing a significant amount of strength
Posted 6 months ago # -
Have you got the post yet? I have a 27.2 GD 4" remote post and will be acquiring a new 2nd hand frame with a 30.9 seat tube.
If you have a seatpost of similar or equal radness we could swap or PX and all reamage gets avoided
Posted 6 months ago # -
TJ, the seat tube on a Bottlerocket is hugely over built and is massively thick. There is plenty of room to ream out to 30.9mm without troubles. As for stress risers, I can't see how that would happen at all, especially with careful reaming.
Posted 6 months ago # -
You can get a custom made longer shim from wheels manuf.
I would defo go 27.2 + shim.Posted 6 months ago # -
You would get a step - a change in cross section where the reamer does not reach.
Overbuilt or not - removing 20% of its strength is a lot.
Posted 6 months ago # -
The reaming is not done in one big hit, it is done in stages and the bottom of the reamer is not square to the tube so end up with a graduated step, not too likely to be a significant stress riser.
Ah well, we'll let the ones we've done in real life speak for themselves
Posted 6 months ago # -
Think I might be inclined to believe what the frame builders/modifiers are saying (18 bikes) on this one
Posted 6 months ago # -
I'd ream it but I think it was an oversight by Transition. It should have had a 30.9mm seatube from the factory, especially as it's designed for what it is.
Posted 6 months ago #
Reply »
You must log in to post.
