I think we will be there Paul

Some good pics arriving Second Daisy Duke for fireplace of the thread / year so far. and good to see the heat-seeking critters

Ohh goody cold and wet instead of warm and wet

The one on the right gets a good review
but the weight and price are wrong

you could fit a Taskled Lflex to the light and as long as the led is still alive
it will work with the 4.2 volt battery pack .

you should be able to get a profile like this

looks nice and tidy around the hearth

the glues used are flexible and I guess so are the nails or screws.

Can you get some in I am prepared to risk it

Is it so bad to post up an email nowadays .

the bots will get your mail probably just after you have signed up for it anyways.
and with al these easy to get mails you can have a throwaway mail addy

Paul. got any Straffe Hendricks quad in

I don’t like water

for me the hopes have been fit and forget items
but then I do put CV joint grease in them when installing .

As its so uncompleted seriously have a think about double skin to keep the damp out as suggested by others

My garage is single skin stone not blocks and this time of year. rust forms so quick on
metal like overnight

My old oily lathe will red up overnight if I don’t cover it with an old sleeping bag .

The only fair way would be man to boar wrestle with only teeth as weapons

Nukeproof Mega is my only bike .
undertrailed for a lot of its riding

So if I read this right any water that gets in will run under your floating floor / Laminate and wont be able to go anywhere cos it will be on a dpm and under the laminate .

Well not me but I am willing to bet that there is some talent on here that could make a good film of that .

Mines up on the bay at the moment if anyone fancies a punt
http://www.ebay.co.uk/itm/120998473514?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

These folks are good

http://www.customcolour.co.uk/

Very old Liberator on the bars

and very new Spidereyes on the lid

the bar light is really not needed as the beam from the spider does it all so run the bar light on low just in case of a failure
but in the spider beam even on high it doesnt show up

beamshot of just the spider 😯

Enjoyed last nights ride Jason and thanks for waiting at the top of the climbs

Report on planet F1

However, di Montezemolo was quick to deny the claims, insisting that two very strong drivers at Ferrari would cause more harm than good.

“I’ve always said that I don’t want two roosters in the hen-house,” the Ferrari president told Italian radio station, RAI.

Pretty amazing how quick he got back down from 24 miles up .

wonder when the other camera footage will be up .

hoping for a good result for. Mark and Lewis to beat Finger waggler
but doesn’t seem likely

Speckled hen

Not a good idea to use a 10 volt charger on 8.4 volt Li Ion battery

Seems like just the thing twitter was invented for. A problem shared is a problem halfed two miserable gits

Rusty has it correct I did try to use the existing driver but it was nowhere near powerful enough for the new leds.

Smudge Lets just say I saw the light 😳

Part 2 is a bit small

First the Lflex needs its thermal double sided tape sticking on

And warm up the housing again and stick in the Lflex in the position shown

Then solder all your wires and job nearly done

the next bit is to read the Lflex manual and configure the driver to 3 or 3.5 amps drive and set the modes and thermal monitoring Job done you now have an approx 2000 lupin Hope vision 4 .

One more little point is the front bezel wont quite close up tight so a little silicon sealant is needed to make it fully waterproof .

Mud is your friend.
just go for a muddy ride and they will be pretty clean after .

just look at how mud degreases your chain

One for Trail rat
you got to love the sound of the old V8
my moment of glory where I won the trial and was the only landy to clean this section .

does it work from non rechargeable AAs if so the that would be 4.5 v so a single Li ion or 2 in parallel would be a good choice

Smudge can do those for you easy and by the sound of it the cable is doable but a fiddle .

Same single Garage a few years ago with the landy project
99% of the work was done inside due to the bastid next door neighbour.

I seem to need a bigger workshop for these little projects now

sold the trialer and it is still going strong the new owner even tested my welding out with a forward roll

Spoke to him this morning
maybe pop him another mail

Must be sommat wrong with me mine get too hot especially after biking so I have to stick them out the bottom to cool off

Mines due its weekly tidy up

If I am out alone I do want to be as bright as the sun to scare the bogyman away.

Anyysredmini
I have not been inside an enduro but have done a joystick and had a look in a Maxx they are not the easiest lights to make brighter .

CB
Nixie has nailed it there I have had a couple of V2 users suddenly find their battery is old and not up to the extra current drain of max but so far no reported huge loss of runtime .

next time I get a vision 4 in I will take some photos and do a how to mod the beast .
but at the moment it seems to be vision 2 s that are dropping through the letterbox

the bezel on the hope 4 Can be rra right Git to remove first a spray with penetrating oil helps
and some marigolds to aid grip .
the oring under the bezel sticks to the optic a d twists it round breaking the legs and removing the led domes this is not too much of a problem as the upgrade replaces the LEDs and driver but does make locating the optic a hastle

vision two thread is here for those who have emailed me
http://singletrackworld.com/forum/topic/hope-vision-2-is-upgradable

I am a floor layer. yes you can get a solvent based vynil seam weld any good carpet shop
will know and be able to get you some

or evilbay for this.
http://www.ebay.co.uk/itm/Type-PVC-Cold-Welding-Liquid-Viny-Flooring-Adhesive-/220201751460

THermocouple is probably dead .