Forum menu
XT rear brake.. Ble...
 

[Closed] XT rear brake.. Bled well, no leeks but still not good.. Options?

Posts: 0
Free Member
Topic starter
 
[#7630019]

So they're in good shape.. The lever was recently replaced and by Merlin cycles and then they were checked over. I bled them a month ago and spent hours leaning, flicking etc to get every last bubble out..

I checked them a few days ago and one or two little bubble came out but not enough to concern me.. The pads are new, the brakes work but the bite point keeps changing.. Sometimes a little closer to the bar than I'm happy with.

What are my options to sort this? Pistons damages, dirty Pistons, new stiffer hoses??

So tempted just to give up and buy some hopes!


 
Posted : 06/02/2016 10:39 am
Posts: 0
Free Member
 

Just buy the Hopes


 
Posted : 06/02/2016 10:57 am
Posts: 4626
Full Member
 

Did you take the caliper off and bleed that with a syringe?


 
Posted : 06/02/2016 10:59 am
Posts: 216
Full Member
 

Have you checked for any other vegetables?


 
Posted : 06/02/2016 11:11 am
Posts: 0
Free Member
 

How old/worn is the disc rotor? Ive found that can play havoc with shitmano brakes.


 
Posted : 06/02/2016 11:16 am
Posts: 43955
Full Member
 

If the bite point is changing (and not always moving in the same direction) then the most likely culprit is air, i.e. your bleed wasn't as successful as you think.


 
Posted : 06/02/2016 11:24 am
Posts: 14
Free Member
 

Apply some cheese sauce and a little paprika.Works for me every time. ๐Ÿ˜€
Seriously though just fire it back to merlin.They've replaced both of mine as mine too where haunted by wee gremlins.


 
Posted : 06/02/2016 11:25 am
Posts: 0
Full Member
 

It can be hard to get all the air out the caliper especially if you've been bleeding it still on the frame


 
Posted : 06/02/2016 11:54 am
Posts: 0
Free Member
Topic starter
 

I have the shimano ice tech rotors.. How much ware is too much..


 
Posted : 06/02/2016 6:36 pm
 poah
Posts: 6494
Free Member
 

use a zip tie to hold the lever down all night and the air should move to the lever then bleed from that.


 
Posted : 06/02/2016 6:56 pm
Posts: 24439
Full Member
 

Does it still happen if you're riding in Wales?


 
Posted : 06/02/2016 7:10 pm
Posts: 0
Free Member
Topic starter
 

zip tie idea sounds good.. With the cap off or on..


 
Posted : 06/02/2016 7:57 pm
Posts: 0
Full Member
 

i assume i'm [b]way[/b] too late to add any more vegetable based puns to this thread???


 
Posted : 06/02/2016 8:29 pm
 poah
Posts: 6494
Free Member
 

just pull the lever hard and put the ziptie on to hold it there. you want the system under pressure to force the air up.


 
Posted : 06/02/2016 9:18 pm
Posts: 11642
Full Member
 

The vid below shows how to get a decent bleed


 
Posted : 06/02/2016 9:28 pm
Posts: 0
Free Member
Topic starter
 

Leeks.... Doh


 
Posted : 06/02/2016 11:29 pm
Posts: 2082
Full Member
 

Are the rotors knocking the pads back ? If the rotors are deformed they'll push the pads back into the calipers. This causes long lever travel and it's overcome by pumping the brake. Pump the lever quickly several times in quick succession and see it the bite point comes further out.

D.


 
Posted : 07/02/2016 12:20 am