Forum menu
Durace bar end shif...
 

[Closed] Durace bar end shifter, Xt sti's, same cable pull?

 ton
Posts: 24278
Full Member
Topic starter
 
[#8293875]

10 spd bar end shifter, 10 spd sti's, are they the same cable pull.

I thought they were, but cant get em to sync.


 
Posted : 18/01/2017 5:18 pm
Posts: 41848
Free Member
 

DA 10 speed was the same cable pull as an MTB 9 speed mech (so works with a 9s mech and 10s cassette), but not a 10 speed MTB mech.


 
Posted : 18/01/2017 5:19 pm
 Duc
Posts: 0
Free Member
 

Different mate. I think Charlie has some bar end ones that will work from Microshift but could be wrong


 
Posted : 18/01/2017 5:20 pm
Posts: 6581
Free Member
 

No, they're not. The 10spd DA bar end shifters will work with a 9spd mtb mech, not a 10spd.


 
Posted : 18/01/2017 5:21 pm
 ton
Posts: 24278
Full Member
Topic starter
 

so if I have just fitted 10 spd durace bar end, to a xt 10 spd block and mech, it wont work.

what do I need?

so I need a 9spd block and mech............aaaarrrrgggghhhhhhhh


 
Posted : 18/01/2017 5:21 pm
Posts: 6581
Free Member
 

There is another way. There will be one of these that will do the job...

http://www.jtekengineering.com/shiftmate/

Edit...
A #6 will do the job...
http://www.jtekengineering.com/shiftmate/shiftmate-6/


 
Posted : 18/01/2017 5:26 pm
Posts: 0
Free Member
 

Microshift http://www.microshift.com.tw/BS-M10_Shifters.html


 
Posted : 18/01/2017 5:34 pm
Posts: 41848
Free Member
 

so I need a 9spd block and mech............aaaarrrrgggghhhhhhhh

No, just a 9s mech, it'll still be 10speed it's just the pull ratio in 10s mechs that's different.


 
Posted : 18/01/2017 5:34 pm
 kilo
Posts: 6921
Free Member
 

Have you checked to see if the shifter can be changed to friction rather than index, iirc some of the older ones can by moving an adjuster


 
Posted : 18/01/2017 5:43 pm
 cp
Posts: 8970
Full Member
 

DA bar end shifters can be operated in friction mode, so no indexing, you just move the lever enough to operate the mech. You quickly get used to how much to move the lever.


 
Posted : 18/01/2017 5:59 pm
Posts: 2320
Free Member
 

Three options to go with your 10spd road shifter and 10 spd mtb cassette in order of extra expense:

[list]
[*]Drill a hole in the arm of your 10spd mtb mech to route the cable and change the pull. [url= http://www.huckingkitty.com/forums/viewtopic.php?f=9&t=868 ]http://www.huckingkitty.com/forums/viewtopic.php?f=9&t=868[/url][/*]
[*]9spd mtb mech (no chance of a clutch)[/*]
[*]Tanpan [url= http://www.wolftoothcomponents.com/collections/derailleur-optimization/products/tanpan ]http://www.wolftoothcomponents.com/collections/derailleur-optimization/products/tanpan[/url][/*]
[/list]

I'd do the first.


 
Posted : 18/01/2017 6:10 pm
 ton
Posts: 24278
Full Member
Topic starter
 

9 spd mech on its way from wiggle.

i hate bikes...........sometimes.


 
Posted : 18/01/2017 10:23 pm
Posts: 43952
Full Member
 

Bugger. I could have given you one!


 
Posted : 18/01/2017 10:36 pm
Posts: 36
Free Member
 

I could have given you one!

You'd have to stand on a box!


 
Posted : 18/01/2017 10:56 pm