My understanding is you would need
10spd rear shifter
10spd cass
10 spd chain

Can keep
Front 9 spd shifter
Front mech
Current c/set ( but could ultimately change rings to 10 spd if they suit your crank)

I think above is correct but may be wrong

I have the Alp X SO and it’s brilliant got mine for just over a £100 by shopping round.
Very versatile by adjusting layering underneath and looms like it will last a long time.

owninga I had some items anodised by Steve @ Acorn less than one month ago . The was on the back of him doing some previous work for me.
Communicated with him via the googlemail email add above no problems at all.
Very strange

I’m on my third set now first set seals failed, second set pedal body came off the axle.
Will see how this pair last !

You can make quite a good one from a A4 sheet of Pace carbon armour , have one on my bike cut to whatever size you fancy. Looks good and a bit thicker than heli tape

Got the Craft jersey excellent bit of kit.
But have just purchased a Rab Vapour Rise stretch top serves as base or mid hence very versatile.
Pricey but a superb bit of kit

Thanks the last one looks good had been looking at this one http://www.ebay.co.uk/itm/280870115648?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649#ht_3566wt_922 which I think was mentioned on the forum a few times.
Take on board getting better batteries any issues with the charger ?
Thanks

Nidderdale Saturday :D

Does anybody know if the above linked light would fit a Joystick mount as I think they fit up to 25mm. The above light mentions body @ 25mm.
Looking at the exposure mount as fitting to a Urge helmet so don’t think the blocks would work

2011 CC here

Forks now swapped to Talas 110/140. Does everything very very well as said drop it to 110 for super steep climbs, or when running at short travel at the rear for instant short travel bike.

Nothing I would swap it for at the moment

Yes like the look of the Stratos but had read it was very thin.

Great when they work now on third set .
First pair seals failed on each
Second pair axle sheared :?

If I must and last ones
Caution pictures may contain extreme cat violence !

Lilly the STW classifieds cat RIP

Grrrr

Fishpus
Kitten

Had our first free of this very forum sadly lost her to a car RIP Lilly
Then went onto get another
A female (marble) house name Fish. Amazing cats and as said quite dog like fetch carry etc. Can go from being very clever to daft as a brush and is now making her self known with all the othe local cats ! But the range and volume of noise it can create is unreal !

Haglofs Endo Active shell here washed and proofed quite a few times now works perfectly.
In fact its that good breathability wise can nearly wear it every day as a knocking about in hoodie.

Thanks geetee

Is there a source for that style of decal set above special order ? Quite fancy something like that on my CC
Cheers

Thanks

How small does the Singletrack pack apple sized ?

I see and good to know you are still with us :D

Changed a little from the shots
Now has shorter stem / black latest XT brakes / Easton Haven bars
Took an age to remove original soul decals along with rim decals etc

Stealthy Soul

Fitted with the Grit stone decals

Which are great as they go from invisible to glowing with everything in between.
Love it

Thanks

Easy to do no bleed req but a bolt and small grub screw to remove to release the lever.
Do the new levers have the adjuster screws ?
If so only above to do
If not you have to remove a small circlip at the back of each of the existing screws to release them from the lever.
Hope that helps

ancient I will send you an email think i found one in your previous posts.
Thanks

Hi
Right back at you foxman
I post my add and respond to you via email with pictures.
I wait ………..nothing
I re-post the add again you respond again so I go back to you again. Once again…… nothing ? I then get another seller ready to go what do I do pop round and serve it to you with a brew and cake ?
Did my very best to sell it to you via the forum and private email am I wrong ?
Edit I too have a family and dont sit at the PC but as said if you had said busy at mo will pay Sunday night etc then it would have been yours

Have you tried centralising the pistons not just the calliper ?
You will find a vid on the Hope site, but basically you put something behind the backing on one set of pads, and whilst squeezing the lever push that pad towards the opposing piston / pads. Then reverse the procedure for the other side, you will see the pistons move out to meet the back of the pad.
I had just as your describing then centralised/equalised the pistons and they were perfect and nice and solid at the lever.
Do this after centralising g the caliper
Hope that helps
Cheers

Thanks tumnurkoz but its the non drive side. Will have a pull apart and see if I can extract some more life, if not as said will get some new ones.
Cheers

Would the rare tool be the plastic thingy mi bob ? as if so the 540’s dont need it I dont think
Or is it an even rarer tool ? :wink:

Thanks gee

+2 for Spesh Enduro XL

Freeagent I have a unused set of pads which I would swap, can’t see an email for you. Mine is in my profile.
Thanks

I’ve got the long fingered ones and they are superb , do what they say in fact nearly sticky !
Very well made but come up very small I’m a L in Fox Endura etc – so ordered a XL based on there sizing.. Anyway ended up with XXL which fit great.
Oh and Amazon were the cheapest.
Hope that helps

Is the PTFE used in the jacket Enduras take on Event ? as didn’t all there waterproof gear used to be Event ?
Also any users how breathable is it ?

YHM

Just fitted one to the front at the weekend replacing a RQ 2.2 which I had F&R as said similar width but not as tall as the RQ.
Still have RQ on rear the Baron was superb at weekend just biting that bit more than the RQ.
Taking nothing away from the RQ’s as also brilliant.
Tyres on Flows and in Chilli flavour

YHM

I found the Alp X to be a smaller/slimmer fit than usual Gore jackets in which im always a L so went XL and it fits a treat

I have a Gore Alp X SO jacket which will do all that plus with the right/extra layers underneath will go through winter. Will also go some way to replacing a full blown waterproof shell, as very water resistant/proof.
Expensive but lots of jackets in one