Forum Replies Created

Viewing 40 posts - 241 through 280 (of 2,644 total)
  • Behind The Scenes: Getting The Shot
  • robhughes
    Free Member

    Yer i could’t find them in his shop granny_ring.

    robhughes
    Free Member

    I look into them Craig.Just don’t want £150’s worth of batteries vanishing.
    Remember the fox shock and royal mail episode.

    robhughes
    Free Member

    Any ideas anyone or who have you used in the past to send li-on’s.Post office is a definite no no.

    robhughes
    Free Member

    looking at couple of threads on here they look a bit of a faf service wise.
    Iv’e got a lot of tools bike and non bike related but seems i need some scaffolding bar off one of our jobs.. 😀

    robhughes
    Free Member

    andylc.
    Was looking at the 350’s off the polish guy have the really got the same internals.

    robhughes
    Free Member

    Thanks for the replies.
    Have been debating the dt’s.
    Isn’t there an ebay guy who does them cheap.

    Found him..

    robhughes
    Free Member

    robhughes
    Free Member

    Dam you.You’ve undone my good work.. 😉

    robhughes
    Free Member

    Ay up i’m getting better. 🙂

    robhughes
    Free Member

    link
    Best i can do.. 😥

    robhughes
    Free Member

    Stick in spokes usually does the trick.
    Bloody trail warriors and on the blue as well.Karma will take care of them when they try out some serious stuff. 😀

    robhughes
    Free Member

    Nar.Stick with our gang…Loco tuning.. 😉

    robhughes
    Free Member

    It must be good as it’s been up and down a hill and through a flooded cycle path……I’m in.. 😆

    robhughes
    Free Member

    Go for it.
    Wait for a good storm then invent shed surfing. 😀

    robhughes
    Free Member

    If it was a medium i’d have bitten you hand off.Can put it on a boil wash for me.. 😉

    robhughes
    Free Member

    ^ Hahaha.
    Brickys sometimes don’t run the damp quite strait so when yoyo’ing up the muck just covers it over a wee bit.Don’t worry it will be there.
    Buildy speak… 😉

    robhughes
    Free Member

    Is Wales now ….ENDURO…WTF…
    That word should be banned on here. 😐

    robhughes
    Free Member

    I’ve hammered the hell out of my five and it’s never even whispered at me.
    As above there all just ally bike frames and not made out of unobtanium.
    Found orange have been great with me.Just to even it out like.
    Saying that mine will probably snap now. 😀

    robhughes
    Free Member

    Hahah.Love those saddles as they me really well.
    Anyone want to buy a 3d lab lappy saddle with a frame attached to it.. 😀

    robhughes
    Free Member

    fd3chris…You got it.Still long though.same length as the five.

    robhughes
    Free Member

    Medium frame but it is the L version.It has flowers on it… 😆
    Look where the top tube meets the seat tube.

    robhughes
    Free Member

    Yep.At least that’s one good thing.

    robhughes
    Free Member

    Yer already considering that chakaping as the shock is just sweet.
    Maybe cut up frame and weigh in in as ally. 😉
    Being an L it will be hard to get rid of.Shame as it is an absolute hoot to ride.
    This wee beastie.

    robhughes
    Free Member

    I know.It’s also an (L)

    robhughes
    Free Member

    Don’t know what to do with the shock yet.It’s got a mint condition custom tuned(LOCO)dhx 5 coil with Ti.Two Ti’s available 325 and 350
    Done approx 20 hours after it was fully serviced at mojo this can be verified by Si at loco.
    Think the shocks worth more than the frame. 😉
    It is the L frame though so this will degrade the price a bit.

    robhughes
    Free Member

    Got mine today.Thanks Steve.
    Really really well made piece of kit.Well done. 😀

    robhughes
    Free Member

    SP41.A must really as it’s the best outer.
    link

    robhughes
    Free Member

    Thanks Steve.If you have sent it out do you mind if i fire it back to for the next batch getting anodized.
    Cheers.

    robhughes
    Free Member

    Cheers Si.When you say adjusters full off.Does this mean that when using the hi and low comp they work at a lower compression rate when re shimmed
    Cheers.

    robhughes
    Free Member

    Si.Can you tune the compression on a mi-co.?
    Got the right spring weight in mine but i struggle to use more than about 125mm even on the big stuff.(u-turn)soft spring (10.1/2 stone)
    Can it be softened down so to speak..
    Thanks for the info btw.RTL-Ti,s are now RCT3’s and running sweet.Now have a pair of RTL-Ti pikes. 😀

    robhughes
    Free Member

    Steve.If you haven’t managed to ano black mine (as par email,i was a bit late)can i wait until the next run and have it done then please bud.
    Don’t mind the wait. 😀

    robhughes
    Free Member

    ^ This and after a repaint from orange i think mine now need about 10mm. 😆

    robhughes
    Free Member

    Are you sure now rickon….
    Come on make your mind up…Only joking bud.. 😀
    TF’s guide.

    robhughes
    Free Member

    Got it.Went into junk for some reason..

    robhughes
    Free Member

    No mail here bud.

    robhughes
    Free Member

    Avid’s own are the best.I just happen to have two brand new sets unopened complete with spare springs,threaded pins and clips.
    Very expensive to buy but i’ll sort you out as i don’t need them.
    Sintered for the front and organic for the back. 😉
    Addy in profile.

    robhughes
    Free Member

    22mm fit’s fine on a five trust me.
    Fox make a 21.84 so 0.16 of a mm is nothing as we are talking about bike frames not tool making.. 😉

    robhughes
    Free Member

    Ano mine as well please.Cocked up so £15 then £2 fired over steve.
    Cheers 😀

    robhughes
    Free Member

    Yes please.
    Mail sent Steve… 😀

    robhughes
    Free Member

    Back at ya..

Viewing 40 posts - 241 through 280 (of 2,644 total)