Sorry should have said video’s whilst diving.Want a cheap gopro alternative really.

Any recomendations or anyone got one in the back of the cupboard 🙂

Kilo

Have messaged you about the mojo.🙂

Oooo…If your getting rid of the myka could well be interested.
Is it the hard tail or full bounce
Pm me please ELShalimo
Edit…Have messaged you.👍👍

That was them
Dam all sold out
Thats for the fast response you wonderful people.😁👍👍
How much for the 6000,s buddy?
Igm….Have messaged you bud.

I have a pair of bollie safery glasses with the yellow tint and they are superb for low light.They really brighten things up and the world looks more defined

Brand x from wiggle super fast delivery and fitted today.Slightly different thread length and 1mm longer.Fits like a glove
Thanks for the heads up Steve
😁😁

Right…Sheared off non drive side so knackered.God knows who tightend this up.
Allen on both ends and still sheared.
Dam
Anyone know what it is for a new one
Cheers

Haha..This seems to be happening a lot.
His last bike paid many many visits to me 😂

Looks like it’s just a standard bolt through according to the spec so mighty force should shift it.Just wondering if its a weird Chinese cheese shaped object.

I have a Lapierre spicy 516 in mint condition with all new bearings and rear bushes that i refurbed last summer and hasn’t been used yet.
It,s in medium flavour.

If you search MTBR there’s a thread on there about a spring that i think folds around one of the shims.I’ll see if i can dig it out as it’s quite common on that damper.
If you pm me your email addy iv’e got one of those dampers here out of a 2014 rev.I’ll hi res some pics to you so you can cross ref against yours to see if you can spot it.
Here you go.
You’ll see the said spring.It’s the first pic in the thread.
http://forums.mtbr.com/shocks-suspension/3-rides-rock-shox-revelation-lockout-not-working-817103.html
Got some high res pics here for you of how it should look if you give me a buzz.
We here in stw land will sort it out for you. 🙂

Mat.
That’s a gearbox problem that is.Iv’e done loads of them and there not expensive.
If you can use a screw driver you quids in.
1-Open door and the make of the lock will be stamped into the steel lock mech.
2- order new gearbox  online
3-undo the euro lock retaining screw and slide out lock by turning key slightly.
4-undo all the screws holding on the lock mech
5 remove and replace gearbox then put it back together
You tube will probably help you.
Go for it mat it’s so easy to do.

Scrap that no stock.

Reminds me of the Blackburn parties 🙂

https://www.youtube.com/watch?v=vlOJiIScXA0

AAARRR Why wont it link direct.Dam technology

O.P Check my for sale add.
Brand new Gortex paclite’s that will fit you spot on. 😉

https://www.superstarcomponents.com/en/slackerizer-angle-headset.htm
There superb quality and £40 with there code on the home page.

That above but don’t forget she must have a nice dial. 🙂
Oopps forgot must be able to whip up top nosh.

Have you tried standing still walking.Looks like much more fun and may overcome your boredom 🙂 

I’m not saying that i WOULD have dropped a chain i simply made it because it was there to be made.  🙂
If i flush epoxy the holes in and air brush the black and silver i could say shimano made it for me.LOL

Quick update.
Works absolutely perfect with no issues what so ever….Result  🙂

My mistake mech is an M772.

It really is very very easy to do but the 9 speed mech needs to be a shadow for this to work.
Don’t worry about the spring as its not connected the the knuckle you are taking out it clips to the parallelogram itself.

Stuff needed
1.5mm drift
2.0mm drill bit
Vice
Hammer
1     Drill dead center with 2.0mm drill bit as you can see in the pic and just drill down until you just see a glimpse of the pins.
Your not drilling out and material where the pins actually sit so it doesn’t effect the strength of anything.
2     Tap pins out with 1.5mm drift(i put a 1.5mm drill bit in the vice and cracked it off just below the drill threads…ideal)
3    They come out easier than you would expect.Take care to not loose the four rubber O rings that sit in recesses in the knuckle you are taking out.
4    Swap over the 10 speed clutched mech and cage (with the four O rings)
5    Refit pins but make sure you turn them trough 90 degrees so that the two barbs(on the end that you are tapping back in with the for mentioned hammer 🙂 ) have fresh ally to grip so they don’t come out.
6    Push the pins through by hand,really easy
7    Then i put where the drilled holes are on the edge of a vice and tapped the pins the last couple of mm so they bite in to the mech using the 1.5mm drill bit drift (sink them 1mm below the surface as this is where they should be).

Job done..:)

But i have lovely xrt m970 shifters Northwind with retro-ed (if that’s a word) i-spec B clamps to zees that i’m keeping.
Mech wasn’t being used so i’ll make sure all is ok then swap the mod over to a M970 mech as i have full xtr goodness on the xc bike .I knew about that way to do it but this was the better option.

Only joking Tom. 🙂
I was waiting for how do you do that.
Pull ratio is not effected as your using the parallelogram off a 9 speed mech.Check the two wee drilled holes.
Mech is an xt m770.
All will be revealed .lol.

What do you want tom my life story……It’s a mech.

Might be this one then.Also info in second link
https://www.reveloutdoors.co.uk/Giant-Anthem-Advanced–Seat-Clamp–34mm/accessorydetail/3-42545

https://www.pinkbike.com/forum/listcomments/?threadid=166760&pagenum=385

I’m in.

In fact can we all chip in and buy a foundry and just make everything out of proper solid iron.That way we should all be safe as.
How long does it take to wear through a set of iron cranks, just in case like. 🙂

Ooo.Look what i have in the stand.Don’t get rid of it as they are a superb bike.Couple off offsets in it and they are hard to beat even with today’s standards.Chuck the coil Lyriks and a custom dhx5 coil on it for big stuff and away it goes.:)
Old pick as now runs 1x

Can some kind sole fix the image for me as my brain hurts with flickr

[/url]
When first built up.Looks very very different now.

This.

Turn the volume up. 😀

Bump for morning dwellers.

Little flat screwdriver with a bit of tape on the end.Stick it in the slot in the center and push.You’ll be amazed how easy they come out and nothing like as tight as a DU.The gap is for getting them out.

The mistake you made was assuming that the rest of the world cares about anodised bling pedals with big pins on their bike. To a 13 yr old a bike is just what get’s them to a mates house to play call of duty or the Spar for 3l of White Lightning. If he’s really lucky he’ll pull a massive skid infont of some girls and pull one of them before graduating to a Corsa and doing handbrake turns in a few years.

You really are a dick aren’t you thisisnotaspoon.Not everybody lives in your weird world.

Cheers all.I forgot to put that he doesn’t ride off road much so shin pads aren’t really an option unless he want’s to look a wee bit stupid in front of his pals.
I thought about the dmr’s kayak23 but have gone similar plastic pinned ones off the bay to see if he can cope with them first.He’s also a little bit slow on the learning level so in hindsight i cocked up giving him the nano’s.It could only end badly hence there now off the bike.

Mrs gnusmas still struggling to comprehend the compassion shown on here

gnusmas.
Why don’t you put her on.I’m sure we would all love to hear from her.As has been said before that we do bicker quite a bit on here but when it comes to the crunch our motley crew seems to come good and pull out all the stops for a fellow biker who could do with a bit of help. 😀

One of these and your away mosey
clock mech

Worn disc of here for buttons and a mech and hands off ebay.You just need to make a plastic disc with a hole in the middle for the clock nut and six holes that will take the disc bolts.Total cost was about a tenner.
Get to it Mosey. 😉

Something like this.
SNV33232 by hughes2025[/url], on Flickr

Another donation to a very very good cause.As said before,sometimes our gang of complete head the balls really do pull together.Well done all.. 😀