He is to busy eating Pasties and cake..
And not racing, making excuses..

Padding isnt too thick, And they seem to dry quickly.

Were very comfy after 3 rides

Usually UK 11 in trainers or Euro 46

I wear a 46 in M200 and AM45’s and also a 46 in DMT E1.
Fit seems ok

Maxle fitment on every one i have had

Is it a Hope Hub??
On them i find you have to remove the axle adaptor 1st, Or it only engages by a few mm

I just brought an x01 cassette, New,been taken off a bike,with that code for £132 off ebay…. Winner

http://www.wychbearings.co.uk/

Sounds like its faulty as they turn really easily.

Are you adjusting the Lever end??

Had a customers whos did this when it was in the back of the car and he was driving.
Said he scared him so much, he stopped and was trying to get out the car and still had his seatbelt on..lol

ESI bar tape is nice.

Have an XL 2015 built up with Pikes and a Monarch plus, with Reverb,X01 groupset, DT 240 onto Light-Bicycle carbon rims, Carbon bars. Fabric saddle. Nobby Nic/Dampf tyres

26.75 lbs

Did have Revelations and a monarch on it and had a nobby nic up front as well that made it 26.2 lbs.

Its a fun trail bike

i use a stanley knife blade, or a very small screwdriver

Mine have done this.
Usually pop the seals out.
Spray inside with GT85/Wd40 and work the bearing inner until it rotates freely. Then blow out with airline and fill with a good quality grease(Blue Marine Grease). Replace seals and refit
Make sure you fit them the correct way around

Check out the new DMR Trailstar.

I am tempted buy it.

Will fit a 2.8 rear tyre

Porridge

It is nasty down here in Cornwall, getting 70mph winds and rain at the moment.
been rubbish since about October, Always raining and windy, trails are a muddy washed out mess.

RIP
An amazing rider.

Thoughts go too his family and friends

Will have a look.

Seems some dont cover for as much.

This is Penny

New Santa Cruz are boost front and rear

Some of the 1st generation 10 speed stuff is now un-available as spare parts.

Sold out and not supported anymore

Lube chain- Ride- repeat

I use Slick Honey on both

Distance 2,122.0 mi
Time 250h 39m
Elev Gain 227,300 ft

Not bad.. All on a MTB

Happy new year

Pretty sure someone like Giant would have enough to buy him, Not sure how many companies could afford him.

Had a few sets of Evolution Fox products. All have been horrible, Terrible dampers in them

Yes, As far as i know, All the same

I use Thor… Cheap to buy and lenses are cheap to replace

If its a Hope XD driver make sure you remove the end cap, This allows the tool to go in fully.

😉

Just fitted RSC’s.

Love the lever feel and control.

Loving my MRP Stage.

1- MP3 and lively tunes and quality headphones
2- Good clothing
3-Warm socks and shoes

As above thats not the correct Conical washer. Hope ones usually have a Parallel section then the taper.

Either that one hasnt been machined correctly or its not for that headset

2-3 eggs, Pepper, Salt,Milk and then quickly mix them up.

Add a small chunk of butter.

Microwave for 1 minute, stir, Then 30 seconds, stir, another 30 seconds stir and eat.

Found that the chunk of butter in it makes it taste the same as made in the pan stuff

Invisframe are now doing certain Decals and custom work

6ft 1.5″ and on a XL 5010
50mm stem.

Is a very good fit for me

Done a few and never had a problem

Had mine for over 1.5 years. Been riding it a lot, and is the bike i use the most.
Fun and fast.

MRP Stage Forks, CCDB Air CS. X01 groupset, X0 Trail brakes, Reverb 150mm. Hope Hubs-Lightbicycle Carbon rims. Magic mary front tyre, Onza Ibex rear.. Just under 31 lbs

If its the newer style with the steel axle(Hollowtech), Pretty sure it cant be done

Any shop with a Fisher account.

SKU Code: WHSPRM50B ,SRAM Spokes & Nipples Roam 50 27.5″ Straight-Pull External Black 281mm (3pcs)