Forum Replies Created

Viewing 40 posts - 321 through 360 (of 593 total)
  • Founders Buy Back Kona Bicycles
  • neilb67
    Free Member

    If its M5 have you tried tapping it out to M6. If its an ally rivnut I cant see why you cant do it. Just keep it well lubed when you tap it

    neilb67
    Free Member

    If its still in there and just spinning them try screwing the pliers back in and pulling it up again…

    neilb67
    Free Member

    I built one into a racecar, does that help?

    neilb67
    Free Member

    I had a similar problem fitting an XT caliper. Ended up using a 180mm adaptor with the 160mm disc. Works acceptable but not brilliant.

    neilb67
    Free Member

    I know Rob was there…

    Rob Crayton Photography[/url]

    neilb67
    Free Member

    They sometimes mark it with paint. 2 or 3 colours. If its painted then speak to a scaffolding company and they will probably know which company uses those colours.

    neilb67
    Free Member

    Have a look on the end of the boards as thats where they normally mark them or on the clamps.

    neilb67
    Free Member

    But Chris thats how the yoof are using them these days on the chase. Just go with the crowd… 😆

    neilb67
    Free Member

    KMC here Chris. Never broke one in all my years of singlespeeding… 😆

    I can pick you up a chain from work if you want. Weve got some we us on decoilers that can turn a 25t coil so should be alright for you…

    neilb67
    Free Member

    ton – Member

    1 pair of vans

    Whose going to drive the other one…

    neilb67
    Free Member

    I had an 03 ex PO van. Got it cheap as I bought it with the usual body damage that most of them have. Repaired and sprayed it at work. Had to fix the rear door lock as they disconnect the central locking by cutting the activator bar. The biggest problem I had was that it didnt have ABS which made it very interesting in the wet or ice.

    neilb67
    Free Member

    Take a good book for the queue at the first bombhole….

    neilb67
    Free Member

    Same here for my van insurance renewal. The renewal quote was near £850. After a phonecall to them they dropped it £150 which made my mind up to not use them anyway. Half an hour on the internet and got a better policy for £450.

    neilb67
    Free Member

    I use one of these. Use it with a screen protector and find it brilliant. I work in the steel and engineering industry so am constantly around grease and dirt and it keeps it perfect. Its so good and cheap that I bought a couple.

    neilb67
    Free Member

    Multi-Use Long Expedition

    neilb67
    Free Member

    Maybe you bumped into each other…?

    neilb67
    Free Member

    Good job your job doesn't involve numbers Rich… 😉

    neilb67
    Free Member

    Takisawa2 is that just outside the craft centre near Swinfen Hall?

    neilb67
    Free Member

    Jesus glad all are ok. Where did it happen?

    neilb67
    Free Member

    Does the Mrs like her new pink floor and skirting boards aswell….? 🙂

    neilb67
    Free Member

    You will need a tool for holding the crank while you undo the pulley bolt ( VAG T20018 ). Normally this means the bottom pulley bolt if FT so will need gunning off with an air gun. So if you have access to a compressor and an air gun then it shouldn't be too much of a job.

    Whereabouts are you?

    Tool

    neilb67
    Free Member

    f5470-a6a5c

    or

    d7910-60e0a

    Both £5 off when £50 spent and end on 30th

    neilb67
    Free Member

    Maybe this is what the AAD stands for….?

    neilb67
    Free Member

    When you changed the freehub did you put too much grease in there and the pawls are not engaging.? Clean out all the grease if you did and try again…

    neilb67
    Free Member

    😀

    neilb67
    Free Member

    Why cant you open it with Memory Map? Just go to <overlay> then <import> then select <GPS Exchange Files> in <Files of Types> and locate the file on your hard drive.

    neilb67
    Free Member

    It will be Swinnertons at Fenton. Give Craig a call and I'm sure he will bring some Mud X's with him

    Swinnertons[/url]

    neilb67
    Free Member

    Right click on the last point of the first trail then select <track> then select <break track>. Then go to the first part of the second trail and do the same. After that not sure how to join the two tracks into a loop if you need but thats a start… 🙂

    neilb67
    Free Member

    YGM again…. 🙂

    Last attempt

    neilb67
    Free Member

    YGM

    neilb67
    Free Member

    I would but can only see win98 driver which i sent you. Do you have link to webpage?

    neilb67
    Free Member

    Ordered my Cadbury's Flake on Sunday and it arrived on Tuesday. Bonus was they put an Inbred frame in the box aswell… 😀

    neilb67
    Free Member

    YGM

    neilb67
    Free Member

    Thanks everyone for the advice. Got a 3GS today. Loving it so far but just got to figure out how to get it to receive my emails from my Blueyonder account

    neilb67
    Free Member

    Cheers everyone, I guess I will go for the 3GS

    neilb67
    Free Member

    Got my last one from Halfords….

    neilb67
    Free Member

    ChrisS, had my first dealings with On-one last week when I bought one of their Inbred frames. First class. Very quick delivery and a nice Cadburys Flake to boot.

    Although I will say my mate got 3 in his box….. 😉

    neilb67
    Free Member

    I sold my 16" Black widow frame last year for just over £400 so I guess you can use that as a guide. But as with anything its only worth that if someone wants it.

    neilb67
    Free Member

    trail_rat – Member

    wheres your helmet ……

    Its the new Giro Grey….

    neilb67
    Free Member

    Mud x if you know the cheeky stuff…..

    ACX if you dont…..

Viewing 40 posts - 321 through 360 (of 593 total)