There is keighley Tree services just outside Crossroads. They’ll deliver as well as charge you per bag filled.

Wouldn’t have any problem with most tools from there but the consequences of a poorly calibrated torque wrench are very expensive. I say no.

Can’t recomend sure term direct enough for this very thing. Same home built camper issues.

Wouldn’t sell mine for that little. No wonder it went so quick.

Couldn’t ride yesterday today I doubt I could swim in it but it would be a close run thing! not happy.

what about this one?
http://www.spokeshirts.co.uk/product.php?productid=16399&cat=0&page=1

The rice thing works in a zip lock bag in the airing cupboard for a week. The rice will pull all the moisture out of the phone, after stripping everything out of it first.

I must be thicker than I though then. That didn’t come to any point worth reading.

Trout, I’m in when’s it avalible?
and as for that 7 up lumi halogen can, blimey, thats quite a bit of heat management required there. But seriously nice work.

Me and cricket bat and wait for it to fall, I’d prefer to underneath it when it dropped. Dam the rest of you!

She sounds impressive, did she being you one too?

sorry I really don’t get it, why would I want to ride and expensive malshaped coathanger?

it is the exceptions to the norm that appear on here.

If they are late fox's can I buy the internals? Seriously can I?

http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs347.ash2/62777_433577053578_628638578_5201171_2190950_n.jpg

Trout it was the 7 up I was looking for actaully. Any idea When you'd have a few in?

Trout do you sell empty housings?

Take the steamer, remove the pipe from the head and hang it over something high away from the walls and plugs. Fill the steamer switch it on and shut the door. If steamers melt the PVA don't get the walls hot. Fill the room with steam from the steamer and the go in with a scraper.

Nick, you'd best come visit to try a pair on then. Specialized defrosters (who said the Americans didn't do irony) are cold boots but very waterproof. Silk liners for the deepest winter me thinks.

we've been told out house cannot be done. 1934 Brick stone built semi. Internal wall were too rough and stone ties stop it flowing to where it should. Perhaps there are just easier ones to do for the money.

have a freeview hd telly but will have to wait till it becomes avalible in 2011.

I use a larger Spline tool, tap it in with a hammer, then remove after soaking the bolt in WD40 or the like, It damages the spline toll slightly but it's quicker then cutting a flat head screw it it.

Well done both of you. And congratulations.

Good plan thanks…..

Oh, nope they're too small.

Bugger.

What tyres for an 8 by 2 concrete cell?

Should should should have gone to see them at thunder city with we were in SA. Didn't and bugger are words that spring to mind.

Found out why. Thought i'd share to help anyone having the same problem. the letters after the bearings name ge-10e is different to the ge-10uk which has a nylon inner thus not float between bearing surfaces.

Not a clue. Used it to watch one film which I paied for and several from the list of free ones. Wasn't too impressed with the quality so I think there was quite alot of compression used from the state of the image.

Got to be worth a try.

Whats wrong with renting a very long ladder and staking the end firmly into the turf so it can work at a shallow angle. Depends how shallow though.

i've got the same problem o the left hand one i can live without it for now. gt85 didn't work

can they do that? I mean the contract is signed and terms agreed already?

got loads of stuff on facebook, we built ours, twice now from a vw t4 mini bus. not as hard as i thought it was going to be but it depends how hands on you want to be. drop us a line if you need more details.

I'm not going to spend a hundred quid on cycling shorts that are smooth and seam free and then cram a pair of M&S Skungies under them just in case my mother asks! Not unless Marks' spend money time and effort to make every seams flat and smooth and invisible for us cyclists, What was that… they don't?

Hope you broke her.

BB Pivot Bearing
6802 RS (1524F) Series Full Complement Bearing – 24mm O.D. x 15mm I.D. x 5mm Width

Dropout Pivot Bearing
6800-2RS Series Bearing – 19mm O.D. x 10mm I.D. x 5mm Width

S-Link @ Frame Pivot Bearing
6802 RS (1524F) Series Full Complement Bearing – 24mm O.D. x 15mm I.D. x 5mm Width

S-Link @ Seatstay Pivot Bearing
6800-2RS Series Bearing – 19mm O.D. x 10mm I.D. x 5mm Width

I did the hundreds of little buggers on my epic, I made a bearing press using bolts sockets and various washers. Appears to work ok, only buy decent bearing.

never shoot in raw, just get the exposure right and you'll be fine.

Thats the type I went out and got, but as Specialized's kit is 40 quid and I spent over that without getting all the little spacers included I'll stick with the kit next time. Besides the economic replacement is not as good as the one that came out of it.

For example, and I'm using ebay as an image resource.

The bearing I've put in looks like this, Dirty looking black jobbie

whereas the one that had to be removed in bits looked like this one Quite shiney but the same spec so to speak.

Is the black one a pile of crap, ignored the magpie in me might regret this.

The bearing are tight in the frame/mount points. it the axle or bolt that appears to be thinner than the inside of the bearings inner race. The bearing I got is the same spec as the model required but do the cheaper bearings have lower tollerances?

All bolts are tight.

Turns out it's also the wrong size. I'll wait and see what they are going to do about it. Either Specialized are wrong and the bike I own was sold with the wrong size bearing or…

This one they sent me is the wrong size.
unreal