thats why i did the lot in one go – save pulling it apart again, even though mine seemed fine bar one

I’d ride them without any worry. Stuffed my rsp Carbon bars on a rock – unless you’re a good few mm’s in, and there are Sharp edges I wouldn’t worry. But that’s me

Rear triangle snapped on the brake mount of my 7 year old fuel ex 7. Trek replaced it with an ex9 rear end to keep it silver, the updated fancy rocker plates and all new bushes/bearings.

Prince’s post Mortem will be performed this morning. At least we’ll finally get to find out if that rib was removed…

Still too soon?

The blacklist

the muc off spray that aldi has just had in, is great for matt and anodised finishes. 4 squid

i have the ribble one too – tend to keep the front wheel touching the ground for added stability. overall a great stand

genesis is dead. exodus and phoenix for movies. s’all i use my hacked kodi firestick for

my old man still has his BandO system from when i was a kid. fantastically made kit

I used to swim with Simon Cooper as a kid. Always was a clever chap

3x 17287 and 1 6903. that replaces all the bearings in the hub and free hub. But i suspect you’ll find only the outer driveside needs doing. i’ll re use the old ones next time around.

and yes, I’ve fitted the Hope Pawls and springs. I snipped a smidgen off the length of the spring to match the SRAM ones. the profile of the pawl is a fraction different, but almost identical. rode 20 miles on sunday and it didn’t skip a beat.

120 quid?

edit: didn’t see the code

just done my rear hub bearings. I used kinetic bearings on eBay.

as far as i know, its SRAM only for the front. they’re a weird size. As for the rear – the bearing numbers are wrong. don’t order 63803, they won’t fit. you need 17287. x3 and 6903 x1

there are better bearings available – but i didn’t want to pay that much for one bearing.
http://www.wychbearings.co.uk/17287-2RS-Enduro.html?gclid=CP-3y4egi8wCFfEV0wodz9kETA

on pulling mine apart, it was only the outer drive side bearing that was knackered. the other were all fine.

if you’re pulling apart, you might want to get a set of Hope Pro 3 pawls and springs, to upgrade the free hub. fit and work perfectly

sold my motorbike on eBay. no sale fees, just a one off listing charge

thread resurrection. came across this whilst servicing my ROAM 30 rear hub. Bought a set of the Hope Pro 3 pawls and springs. The Pawls are almost identical. the springs were a tiny bit longer, so i snipped off a fraction. Installed and ridden. work perfectly.

I’ve just run a half marathon. last one i did was 12 years ago. I don’t run at all normally. I have a pretty good base level of fitness. I just started with about 3 miles, and ramped it up each week. Ran 3 times a week at most. One of those was a bit of speed work, sprinting every fifth minute. longer run on saturday morning. I tried following a half marathon plan off the web, but found it too demanding time-wise. 6 runs a week was too much.

Finished in 1:30:27, which i was pretty happy with

good luck!

pound land had some in last year, which worked pretty well. hoping they’ll get some more in!

TPS are great. Just had cam belt and tensioners done on my Leon. Pretty sure it’s every four years or 60k

Had a pair of the gloves last year. The gel pad seems to be in a weird place to me.

In store leaflet probably

i think the graphics visually mislead you into thinking they’re rolled back a lot. get on with mine fine

@elgolfo – wore mine yesterday for the wilmslow half marathon – same reaction!

got my PB too, so well happy.

curved is a gimick. but my old man bought a 4k one, and its flipping brilliant. id have one

Thought that had been patched now, with an updated download of transmission. Read about this a while back.

yes, all doable in a hilly 40 miler.

yes, the bearing is in there too – so i just tap it out then, yes? cheers Ben

opusone – you can link up the standard forest loop with plenty, depends on your legs. heading into the goyt, or out into three shires.

just out of warranty by how much? contact the manufacturer and politely ask if they would help out? always worth a try

yes, that would be great – ideally i want one that support 5ghz, but if thats not averrable, then that will do nicely. cheers!

“Renovo Badash, just needs the ugly derailleur removed.”

id rather burn that, than be seen on it :O

and well inside

http://www.richersounds.com/product/av-receivers/denon/avrx520bt/deno-avrx520bt-blk

have an older model, and very happy with it

smidge over budget

http://www.richersounds.com/product/av-receivers/denon/avrx2200w/deno-avrx2200-blk

called craig at kinetic bearings – apparently SRAM used the seal from 63803 on the 17287RS bearing. its the 17x28x7, not the 17x26x7 as marked. ijeets

i just ordered these for my roam30’s

http://www.ebay.co.uk/itm/201369093140?_trksid=p2057872.m2749.l2649&var=500561300958&ssPageName=STRK%3AMEBIDX%3AIT

so I take it these are wrong ?!?!

Time xc6 for me. Used candys for a while as I got them cheap. Buy cheap, but twice. Time just work.

My old man just bought a Brennan b2 to ditch all his discs. Works great

My money will be going on the orbea when jnr outgrows his bonaly 24

As above. Sam smith over radiohead – retarded

Wore mine yesterday – dead comfy and light. **** Cancer is a well known phrase, despite being a bit sweary. I have no problems wearing with pride!