may have been done, Easton Haven carbon bar for £40 at chain reaction. Just picked one up, bargaintastic!
link

But…I…don’t…neeed…one……

damnit!

Cheers. Needed some new bars.

Was convincing myself I needed some new bars…. But I dont

Super narrow!

retro narrow 😉

Cannock friendly

Still the ideal width around here – and only feel too narrow when my hips have got stiff so I can’t get my enduro-shimmy on…

Thanks OP, pair ordered. 🙂

Amazing deal, perfect width for a trail eel like myself

Fisrt, 711 is not super narrow.
Second, Damn Damn Damn, I bought mine second hand for more than this.

I sold a second hand set for that much 😯 Lovely bars but I fell victim to Bar Inflation and had to replace everything with 760s.

Recommendation :
1) Buy these bars
2) Don’t ever ride a bike with wider bars

They would go well on my hardtail. Must resist!!!

have been running raceface turbines at 725mm wide, sacrificing 14mm for the sake of some carbon bling…

Damn if only it was the Havocs

Ta! 😀

Northwind – Member
I sold a second hand set for that much Lovely bars but I fell victim to Bar Inflation and had to replace everything with 760s.

Same here. Lovely bars, too narrow.

Lovely bars, and on their way for the second bike…. Bargain!

Such a bargain I’m tempted to get a set and then build a bike around them.

Recommendation :
1) Buy these bars
2) Don’t ever ride a bike with wider bars

😆

Very true.

I got some Havocs from my mate who’s Mrs works for the old distributers and gets them at almost trade. They cost more then that!

Cannock friendly

Also just right round lustleigh cleave 🙂
Cheers op – good psa. Purchased

Shame they’re not flat 🙄

A big thanks to OP from me for this PSA. I received mine this morning and they are quality (come in an Easton box with literature etc), and an absolute bargain at £40. 711mm is just right for my riding.

Had a quick look on the Easton website and it appears that they are increasing the width in the latest season’s Haven carbon bars from 711mm to 740mm so I assume these are now ‘old stock’ and being run out.

Stock is still showing on Chain Reaction site…

Mine arrived today too – replacing EA70 685 bars. Off to morzine now and as i’ll be holding on for dear life riding the rockhopper down the runs while the Wife rides my big bike, thought it right I treat myself 😀

And mine! They’re going on my PA, current 685 EC90s going on wife’s new Swift.

Annoyingly, Wiggle sent the wrong front mech, so I ordered another from CRC + some tyres. Thought about voucher codes at the checkout, but didn’t think to open the box under my desk!

They have a lot of them in stock! (I added 100 to my basket)

Arrived this morning and fitted to my Anthem, together with a 60mm OD2 stem I found on eBay. I have these bars on my Trance and they are great, especially for £40! Off to play at Swinley later. It’ll be interesting to compare the difference on the Anthem, having gone from 100mm stem and 685 bars. I hope it still climbs…

mine arrived today, and my god they are light! Looking forward to getting them on the ‘Do It All’ bike and going for a spin. My Spank 777 bars were just too wide for the local woods, so this should be a nice improvement 🙂

Good shout op,mine also arrived this morn’,very stealth looking too.

Bah gave in an ordered some 🙂

Mine came today too. Lovely looking bars, look great on my ti ego chariot 8) Just been fitted but not ridden yet. Day off tomorrow to try ’em out though. Wahoo! 😆
Replacing a pair of aluminium 711mm havocs so should feel the same but betterer.
Thanks again op.

I hate this forum! Too much info!

Just ordered a set for my HT, yesterday having bought some 740mm Fatbar Lites for my FS….. 🙄

Stop taking this thread to the top (just ordered a pair too)

I did NOT need a new pair of bars (why is it a pair??).

(why is it a pair??)

Theres 2 handles on most bars.. hence pair

cheers 😀

Just bought the Alu ones and now I have to try to justify buying more.

i took mine off after seeing a mate snap his carbon ones at llandegla a few weeks back. Bought the alu ones.

They are very very nice though.

What torque is needed on these at the stem? Or is it just as normal, backed off a bit 🙂